Αυτόματη γραμμή ψεκασμού βαφής είναι προς πώληση. Εργοστάσιο/Μάρκα: MAKOR. Έτος κατασκευής το 2010.
Δεχόμαστε προσφορές έως και την 9η Σεπτεμβρίου. Ελάχιστη αρχική τιμή η 60.000€.
ΤΕΧΝΙΚΗ ΠΕΡΙΓΡΑΦΗ (ΣΤΑ ΑΓΓΛΙΚΑ)
Line speed: from 1 to 4 m/min. – it depends on flash off time, amount of paint applied and quality required.
Pos. 1) M1A001P
BELT CONVEYOR mod. ROLLY 2000
The belt conveyor ROLLY allows connecting the transport systems of the machines in a line. It is used at the entrance and at the exit of a line to make the load and off load phase easier.
TRANSPORT SYSTEM
- The transport system is located inside a solid steel structure.
- The transport belt is made of synthetic material, abrasion and chemical agents resistant.
- Forward feed is adjustable by inverter, installed on the control panel of the machine close by.
Pos. 2) L1A001P
BRUSHING MACHINE, mod. ROTOFAST with n. 2 brushes
This machine has been designed to guarantee a perfect cleaning of the panel before the painting phase. The dust is completely removed by a brush, rotating blowers and a deionizing bar.
TRANSPORT SYSTEM
- All the components are hosted inside a cabin designed for easy set-up operations.
- The transport belt is made of synthetic material, abrasion resistant. It can work at different speeds set by a potentiometer.
PANEL CLEANING DEVICES
- The brushes installed on a shaft, 45 mm diameter, are made of natural fiber and can have also a spiral shape.
- After the brushes there are rotating blowers that can remove possible dust left on the panel and the dust is conveyed towards collecting conduits. Thanks to a piece detecting sensor the blowers work only if necessary. This allows saving compressed air consumption.
- The deionizing bar is located before the rotating blowers and eliminates remaining electro-static
Technical data belt conveyor mod. ROLLY 2000
Overall dimensions (L x W x H), mm: 2000 1600 900
Working height, mm: 900 ±50
Electric current Frequency, Hz: 50
min max Feed speed m/min 2 10 ± 5%
Feed motor power (nominal), kW: 0,55
Total installed power (+~5%) kW 0,60
Pos. 2) L1A001P
BRUSHING MACHINE mod. ROTOFAST with n. 2 brushes
This machine has been designed to guarantee a perfect cleaning of the panel before the painting phase. The dust is completely removed by a brush, rotating blowers and a deionizing bar.
TRANSPORT SYSTEM
- All the components are hosted inside a cabin designed for easy set-up operations.
- The transport belt is made of synthetic material, abrasion resistant. It can work at different speeds set by a potentiometer.
PANEL CLEANING DEVICES
- The brushes installed on a shaft, 45 mm. diameter, are made of natural fibre and can have also a spiral shape.
- After the brushes there are rotating blowers that can remove possible dust left on the panel and the dust is conveyed towards collecting conduits. Thanks to a piece detecting sensor the blowers work only if necessary. This allows saving compressed air consumption.
- The deionising bar is located before the rotating blowers and eliminates remaining electrostatic charges to avoid attracting other dust.
Technical data brushing machine mod. ROTOFAST
Overall dimensions (L x W x H), mm 1300 2100 1600
Working height mm 900 ±50
Electric current Frequency, Hz: 50
min max Feed speed m/min 2 8 ± 5%
Brush rotation speed rpm 450
Brush diameter mm 200
Compressed air consumption Nl/min 8400
Feed motor power kW 0.75 Nominal
Brush motor power kW 1,1 x 2 Nominal
Total installed power (+~5%) kW 3 Nominal
AUTOMATIC OSCILLATING SPRAYING MACHINE mod. KRONOS equipped with 2 product circuits to apply 4+4 guns and 2 pumps. Lexan cover on in-feeder and out-feeder.
KRONOS is a machine easy to use and with solid construction features. It is the ideal machine for a customer who wants to turn the manual finishing line in his painting department into an automatic line.
The innovative belt cleaning system patented by Makor allows reducing the maintenance costs and to optimize the use of the paints, especially when using products to be recovered.
TRANSPORT SYSTEM
- Solidly anchored to the sturdy steel structure the transport system is equipped with a 1653 mm wide antistatic belt, easy to replace, interposed between two PVC belts.
- The belt cleaning system operates in two clearly distinct phases: during the first phase a mechanical scraping of the surface is made, during the second phase the belt is soaked and afterwards it is dried by means of appropriate gaskets.
- The product that has been removed from the belt is conveyed automatically into a collection container and if it is chemically recoverable it can be completely reused.
- The operation principle and the accurate structure of the cleaning system allows reducing the daily consumption of solvents to an absolute minimum
SPRAY UNIT
- Both gun holding carriages are prearranged for assembling 8 guns fed by two independent product circuits (one low pressure and one Airmix or Airless).
- The oscillation of the spray units occurs through a motor managed by inverter in order to obtain a maximum operation speed without any vibrations.
- The opening and closure of the spray guns is based on the scanning of the work pieces by means of an electronic reading bar placed at the in feed of the spraying zone.
- The spray parameters are set by the operator by means of a practical graphic coloured display. The skilful use of the symbols and images makes it a simple and intuitive instrument to use.
MANAGEMENT OF AIR FLOWS
- The perfect symmetry of the pressurization and aspiration ducts guarantees a homogeneous distribution of the air flows inside the spray cabin. The air capacities are adjustable by means of appropriate valves.
- Double filtering cells in air inlet ducts allow having clean air inside the cabin. The spray dust in the exhaust ducts is intercepted in the same way by means of dry filtering cells.
Machine includes:
- 4 low pressure Kremlin guns mod. A25 complete with nozzle;
- 1 low pressure Kremlin pump mo. PMP 150 – max. capacity 19 nl/min. 1:1 compression ratio
- 4 air mix Kremlin guns mod. AVX complete with nozzle
- 1 air mix Kremlin pump mod. 20.50 on cart – max. capacity 6 nl/min. 20:1 compression ratio
Technical data
Overall dimensions (L x W x H), mm 4700 3850 2950
Working height mm 900 ±50
Electric current Frequency, Hz: 50
min max Feed speed m/min 1.8 10 ± 5%
Suction air capacity (~25 m/s) m3/h ~18000 At suction outlet
Feed motor power kW 0,75 Nominal
Reciprocating start up motor power kW 5,50 Nominal
Air inlet motor power kW 2 x 1,10 Nominal
Suction fan motor power kW 7,50 Nominal
Total installed power (+~5%) kW 16,80 Nominal
DRYING TUNNEL equipped with:
This tunnel has been realized to be very flexible in order to host different kind of thermal components used in the flash off and drying process. This oven is the ideal machine for the flash of and drying of water based and solvent based UV products.
STRUCTURE AND TRANSPORT SYSTEM
- Panels are moved by rollers in zinc motorized by a double row of parallel chains.
- Transport speed can be adjusted in continuous through a potentiometer.
- The tunnel is insulated to save energy.
- Side doors along the machine guarantee an easy access.
4a) FLASH OFF OVEN THERMO ZONE
- 4 meters with laminar air
- 6 meters wind jet air with heating battery and n. 3 IR lamps, with power adjustable in continuous
- 2 meters TL lamps (n. 18 lamps)
Technical data
Overall dimensions mm See layout
Working height, mm 900 ±50
Electric current Frequency, Hz: 50
min max Feed speed, m/min 2 8 ± 5%
Intake air capacity (~25 m/s), m3/h ~7000 At suction outlet
Suction air capacity (~25 m/s), m3/h ~7000 At suction outlet
Coil thermal power, kcal/h 40.000
Feed motor power, kW 0.75 Nominal
Intake motor power, kW 4 Nominal
Suction motor power, kW 3 Nominal
IR lamp power, Kw 5X3 Nominal
TL lamp power, kW. 3.5 Nominal
Total installed power, kW. 30 Nominal
4b) UV OVEN:
UV LAMPS
- A lamp cooling system allows maintaining the bulbs at an ideal temperature. This is for a longer life and better performances.
- Upper lamps are positioned obliquely in respect to the transport system and can be adjusted on the lamp axis in order to address the UV rays on the upper side of the panels and on their edges guaranteeing a total curing.
* considering mono-phase lamps.
4C) 2 meters extension at the exit to pick up the pieces
Number of lamps 3 upper
Bulb working length mm 1400
Lamp specific power W/cm 80
Lamp power kW 12
50Hz
min max Feed speed m/min 1.9 11 ± 5%
Suction air capacity m3/h ~2000×3 At suction outlet
Feed motor power (with inverter) Kw 0.55 Nominal
Suction motor power Kw 3×1,5 Nominal
Total requested power (+~5%) Kw 43 * Nominal
* considering mono-phase lamps.
4C) 2 meters extension at the exit to pick up the pieces
[schema type=”product” name=”MAKOR Automatic Spray Painting Line” description=”MAKOR Automatic Spray Painting Line. Construction year 2010. ” manfu=”MAKOR” price=”60000EUR” condition=”Used” ]